Home > Error Code > Jacuzzi Hot Tub Flo Error

Jacuzzi Hot Tub Flo Error

Contents

The Flo code was still there. Could also be low water level. Also standard in the Platinum™ Series is our Hybrid Clear Water System and 150 sq. PSoH = Pressure switch open with high pump. navigate here

FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. BioClean Filters™ which provides more clear, clean water while lowering maintenance. Turn ON the spa. If necessary, reset breaker.

Jacuzzi Hot Tub Flo Error

I have replaced every part of this hot tub all the way done to the wires and sensors. We offer 6 different models in our Swim Pro™ line. If one of these sensors needs to be replaced BOTH should be replaced at the same time. Thank you!

or Solid FL, FLO, and FL2 mean one of 2 things. FLO2 = Closed or shorted flow switch on system startup Pinnacle OH = Temperature has exceeded 110° F SN = Sensor failure FL = Flow/pressure switch stuck in closed position Spa can clog this return fitting. Jacuzzi Error Code Fl1 Consumer Reviews EasyPak Spa Controls "Very pleased with the ease of installation and all the diagnostic features that other spa packs did not even have.

The Escape™ Plus Spas have 60 to 64 jets. Hot Tub Error Codes November 26, 2015 at 7:09 AM Ironman101Qc said... I de-powered it, re-powered it and it still won't cycle. characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 10 2826351 FREE Shipping on Cal Spas Covers!

Check your spa's water level, if the water level is too low turn off the spa at the GFI, fill the spa, and then turn it back on. Flc Error Code On Hot Tub Sundance Spas ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific) Hold = Panel buttons pressed to many times However, there are four led lights in a square fashion that blink every 10 seconds. Started in the industry working for a Cal Spa factory store.

Hot Tub Error Codes

Patio™ Spas Round PZ-511R Balboa PZ-517L Vista PZ-617T Kona PZ-525L Hawaiian PZ-621L Pacifica PZ-722L Tropical PZ-722B Patio™ Plus Spas Balboa PPZ-525L Vista PPZ-628T Kona PPZ-537L Hawaiian PPZ-631L Pacifica PPZ-732L Tropical PPZ-732B Did you check the gate valves to make sure 1 of those is no partially blocking the flow, causing the DR error and the pump to over heat? -Jay Leave a Jacuzzi Hot Tub Flo Error The filter will not go off any ideas? Balboa Hot Tub Error Codes Note: The control system brand name is usually different from the hot tub brand name.

Turn off main power. http://alltechgossip.com/error-code/what-is-a-socket-error.html Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated. These parts are easily and inexpensively replaced. This sometimes refreshes the pc board software if there is anything funky going on. How To Fix Flo Error Hot Tub

If I spray into the pump with a garden hose, there is warm water entering the tub. Spa is shut down. (Displays on third occurrence of dr message.) Follow directions for dr message and press any button to reset spa. The filter is clean and both pumps run and the flo switch is new. his comment is here If the pump seems to be working then I would disassemble it to inspect for any blockages from hair, etc.

ft. Where Is The Flow Switch On A Hot Tub Wait up to 1 minute to see if the error clears itself,if not reset the tub by turning off the GFI breaker, wait 1 minute, and then turn the breaker back Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated).

OHS = Overheat.

rdr Every 90 days Drain and refill spa rC0 Every 180 days Clean and condition spa cover rtr Every 180 days Treat wood panels rCH Once a year Replace the filter No LF or dry warnings. An important thing to remember is every time you try one of the troubleshooting steps you should reset the tub's GFI breaker to clear the error out of the topside control. Artesian Spa Error Codes I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address

It's flashing a code and lighting up pump 2 light. This whining sound can be a sign of a clogged impeller or a bad motor. Here's what to do if your spa throws a FL, FLO or FLOW error code at you. weblink After many uses, the temperature seems to go down one day, then went back into normal, 105°.

Remove the spa cover and allow water to cool. All Rights Reserved. I am lost. Both are secured with black plastic nut around the gray cable.

Once again these can be caused by a flow issue. Contact Info Precision Pool Construction 83 Haverhill Rd. I have also tried shutting the hottub off and turning back on with out the filters installed. I have everything hooked back up the way it should be with a new board.

Questioner's RatingRating(1-10)Knowledgeability = 10Clarity of Response = 10Politeness = 10CommentNo Comment Add to this AnswerAsk a Question Related ArticlesAutomotive Questions and Answers -Automotive Questions and Answers -Volkswagen Jetta Won't Start Or Failure of the pcboard is rare for this but can happen. Why a Marquis Spa for Your New Hot Tub? Flow problems are the number one source of trouble for the spa or hot tub owner.

Overview Awards Factory Tour Contact Us Sitemap Careers Privacy Policy Public Relations In the News Press Releases Cal Spas on TV Backyard Ideas Blog Dealer Resources Log In to Dealer Connection I bled it, and tried the pump and it seems to circulate the water, but will not cycle properly. Ask Brian Your Own Question Brian, Architect Category: Home Improvement Satisfied Customers: 3123 Experience: Licensed Architect- 17 years, L.E.E.D. Press any button to reset or wait 15 minutes and spa will automatically reset.

Spa has shut down. It's either a "horizontal" heater like a vertical heater like or a "U" style heater like this Spas with a horizontal heater has a PRESSURE SWITCH screwed into I replaced the mother board twice, the motor and wet end, I've tried 3 new flow switches, new filter, new topside control, new hot and cold sensors. If it is circulating on low speed and will not engage to high speed it could be the motor as well.

I still have a FLO code. IF proper voltage is present, then you need a new pump/motor. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.

Top