Home > Buffalo Terastation > Buffalo Terastation Error E16

Buffalo Terastation Error E16

Ich werd mich dann mit einem Update melden Wenn Ihr noch andere Tipps für mich habt, bin ich natürlich für alles offen ___________________________LinkStation Pro LS-XHL FW:1.37mod1 by Shonk Do 27. Replace the hard drive if there is error occurred after rebooting the product. If you utilize our service, Buffalo will send a replacement device to Datarecovery.com to replace your in-warranty failed NAS device. But I had to enable PHY15 jumper and copy the from my old disk directly. Check This Out

Any suggestions anyone?Thanks. If the LED still turns on, contact Buffalo technical support for assistance. E30: Professional data recovery for all Buffalo external hard drives, including Buffalo TeraStation and DriveStation products. 100% data recovery guarantee. Im Systemtray bzw im Linkstation Navigator wurde die LS auch durchgehend erkannt.Nun kommt seit dem nur mehr nach dem hochfahren der LS der Fehlercode E16 ( Ein langes rotes Blinken und

E15 Hard drive cannot be found. E12 The system temperature has exceeded the safety value. Note: The error may also be viewed from NAS Navigator2.

Operation will continue, but in degraded mode. I then tried the "reset to factory settings". Contact Buffalo technical support for assistance. Ich habe selber die LS-XHL.Das Update läuft auf WinXP ohne Firewall immer durch.

Flash auf FW 1.4 hat aber auch nicht das gebracht, was ich erhofft habe, somit habe ich jetzt auf die Firmware 1.37 von Shonk zurück geflasht.Danke nochmals! ___________________________LinkStation Pro LS-XHL FW:1.37mod1 Please call for more detailsBuffalo Linkstation & Terastation Recovery Tips As mentioned above, chances of a successful recovery are much higher if a device is turned off immediately when an error I20 Formatting the hard drive. This is especially true when a hard drive failure caused the data loss.

E30 An error occurred, so hard drive X was removed from the RAID array. In most cases, Buffalo Terastation devices are recovered in-lab. Don't show me this message again. Also, the items … E16: HDx Error E16 … Replication and choose "Resync" to execute resynchronization.

  1. Raid Data Recovery from following File system: Netware NSS, NWFS Servers, NTFS, XFS, FAT32 … Buffalo TeraStation Pro.
  2. Mein nächster Versuch war über das TFTP Paket ( für alle 4 Modelle) das Ding quasi neu auzusetzen. Über TFTP bekomme ich aber leider keine Verbindung zur LS, habe versucht die
  3. Can't Mount HDx Error E16 Unable to find hard drive X.
  4. Top Profile Reply with quote tdamgaard Post subject: Re: E16 - unable to locate internal HDD (HS-DH500GL)PostPosted: Sun Dec 06, 2009 7:47 pm Offline Newbie Joined: Mon Mar 03,

E16 Hard drive cannot be found. Data is distributed across the drives using backward parity rotation. Top Profile Reply with quote tdamgaard Post subject: Re: E16 - unable to locate internal HDD (HS-DH500GL)PostPosted: Tue Dec 22, 2009 3:19 pm Offline Newbie Joined: Mon Mar 03, Also teste es auch mal am Router.Viel Erfolg!

Please do the following if this happens:

Shut down the LinkStation. his comment is here If no DHCP server is available, then an IP address will be assigned as follows: IP Address: 169.254.xxx.xxx (xxx is assigned randomly when booting the TeraStation.) Subnet Mask: 255.255.0.0 "hdusers", "admin", Note:The function LED (blue) and the info/error LED (orange) blink together if an error occurs during DirectCopy. This is the default configuration for some devices.RAID 0: Data is distributed across the drives.

intill reboot. Don't waste yourtime. I had this same error 16 with a WD10EADS-00P8B0, and changed to WD5000AAVS-00ZTB0, which is a 500GB WD Green with 8K buffer, and that worked fine.It seems the drives ending in this contact form From the Web Admin interface, navigate to [System]-[Failover] to reconfigure the backup TeraStation for failover.

This configuration is rarely used on Terastation devices.Supported DevicesData recovery is supported on all Buffalo devices, including the following:LinkStation™ ProLinkStation™ MiniLinkstation™ DuoLinkstation™ QuadLinkStation™ LiveBuffalo TeraStation™Buffalo TeraStation™ DuoBuffalo TeraStation™ IIIBuffalo TeraStation™ Pro Replace the hard drive. However, it seems to boot ok, and transfers to the unit appear to work too.

E14 The RAID cannnot be mounted.

RAID arrays can fail. Sorry. Fan Failure SYSTEM Error E12 A rise in the system temperature may have exceeded the allowable safety value. Link/Act LED Status Descriptions Solid green Linking Blinking green Accessing AC adapter LED Status Descriptions Green A power outlet is connected to the AC adapter (power is connected).

I tried to put a jumper on 5+6 to force 1.5GB PHY but that didn't help at all. Check that there are no objects around the LinkStation, or install at a cooler location. I22 Erasing the data of the hard drive. navigate here Set the hard drive again after shutting down the LinkStation.

After the LinkStation shuts down. I11 The invalid sectors of the hard drive may reach a dangerous level. Bringe sie durch wiederholtes vom Stromnetztrennen nach 65 Sekunden in den EM- Modus. Format and Disk check will also complete successfully.

Replace the failed drive indicated by the red LED. E23 An error occurred, and the hard drive was removed from the RAID array. Error LED The info/Error LED blinks red to indicated an error. is it actually working ok, even though E16 shown?

Email *Required Your Feedback *Required Refine your search Select Product / OS & Hardware Network HDDTeraStation31,32Network HDD,TeraStation Select OS & Hardware Enter Keywords or a specified ID BUFFALO_GLOBAL BUFFALO GLOBAL [EUROPE] I32 Appears when RAID rebuilding or formatting on the web Admin interface is necessary after replacing the hard drive. Apr 2010, 23:32Beiträge: 5935Bilder: 309 Bedankte sich: 169 malErhielt: 773 Danksagungen in 715 Beiträgen Re: Linkstation Pro LS-XHL Fehlercode E16, bitte um eure Hilfe Deine LS ist noch zu "gesund" I25 Updating the firmware. *Do not turn LinkStation OFF during the update.

The number of flashes is the ones place of the error code. Welcome, Guest. Jan 2011, 11:11Beiträge: 13 Bedankte sich: 4 malErhielt: 0 Danksagungen in 0 Beiträgen Re: Linkstation Pro LS-XHL Fehlercode E16, bitte um eure Hilfe Hi!Danke für die Tipps, du hattest absolut Once all of the hard drives have been properly imaged twice, a RAID specialist will then work to "de-stripe" the disks. "De-stripe" is a term used by us to describe taking

I used FW 1.15.From a cold boot, I get the red LED showing code 16.

Top